Sikkens Cetol BL Deck & Wood Cleaner

Sikkens Cetol BL Deck & Wood Cleaner

$23.05
financing available

or 4 payments of $5.76 AUD with Afterpay Info

or 4 payments of $5.76 AUD with Afterpay Info

Sikkens Cetol BL Deck & Wood Cleaner A fast-acting gel that revitalises and brightens timber. Ideal for large surface areas such as timber decking Easy to apply, Easy to clean,...
financing available

or 4 payments of $5.76 AUD with Afterpay Info

Sikkens Cetol BL Deck & Wood Cleaner

A fast-acting gel that revitalises and brightens timber.

  • Ideal for large surface areas such as timber decking
  • Easy to apply, Easy to clean, Easy to use!
  • Act fast

 

Before Use:

Pretreat new exterior hardwood and decking with Sikkens Cetol BL Tannin & Oil Remover.

In the case of old and weathered wood, remove excessive dirt with a stiff bristle brush. Only suitable for use on bare and previously oiled wood. 

Before Application, wet the timber to delay drying out during application. The surface must remain wet during the whole application process. Do not let the wood dry out with Sikkens Cetol BL Deck and Wood cleaner coated on the wood.

 

Applications:

Use Sikkens Cetol BL Deck and Wood Cleaner to brighten and revitalise grey, weathered timber in preparation for application of new timber coatings.

Stir thoroughly before use. Wearing suitable protective gloves, apply liberally with a brush or mop. The wood will start to lighten in colour.

Immediately after application, work into the surface of the wood, using a mild adhesive scrubbing pad or stiff bristle brush. Leave to stand until no further lightening occurs, but for no more than 15 minutes. Work manageable areas at a time so that the surface remains wet throughout the process.

Wash off with plenty of water using a hose, ideally using a power hose on a fan setting, until the water runs clear. Allow the decking to dry thoroughly before applying a suitable Sikkens coating (such as Sikkens Cetol HLSe Decking Oil).

In cases of severe weathering or highly tannin rich timbers (such as Merbau), the process may need to be repeated again before applying a topcoat. 

 

After Use:

Remove as much cleaner as possible from brushes and equipment before cleaning with water. Do not use or store in extremes of temperature or wet conditions. Clean up any spills while still wet. 

 

Drying Time:

Allow to dry thoroughly before applying a protective finish or topcoat. When using an oil-based system, allow to dry for at least 3 days. 

 

Coverage:

Smooth planed timber: approximately 8m² per litre.

 

Clean Up:

with Water

 

Caution:

Do not apply in temperatures below 5 degrees C or if rain is likely before the job is complete. Protect any areas around the deck being restored to minimise splashes and staining. Avoid contact with grass or plants. If contact occurs, dilute splashes with copious amounts of water. 

 

Pack Sizes:

Available in 1 and 5 Litres

 

 

Paint Calculator is super feature that gives clear understanding for amount of paint  requires for painting project.  In nearest future we can calculate labour cost for the painting project. Usually for 3 bedroom unit/house required amount of paint for ceilings is 20L  in most cases its flat (bathroom ceilings best to use Mould proof paint or simple low sheen paint, 30 litres of paint  for walls usually its low sheen, and 4-6 Litres for wood work.if its new surfaces you must apply sealer/primer undercoat.
Coverage in most cases around 1L per 10 Square meters Again its for previously painted surfaces only. For new plaster board its around 8 squares per 1 L, and new render is 5-7 square meters per one litre of paint.

Paint Calculator
room
← Go back

Customer Reviews

No reviews have been published Write a review

Related Product

params.svg
Panel Tool
Float header
Float topbar
Default Boxed Large